General

How do I know if the horse blanket is sitting correctly?

How do I know if the horse blanket is sitting correctly?

The buckle at the front of the chest should not be too tight. Otherwise there will be pressure or chafing points on the bow joint. On the other hand: If it is too wide, the blanket slips back, pressing on the bow joint and withers. You should be able to easily slide one hand through the front, then the blanket sits correctly in front.

Which profiles for ceiling hang?

Material list: you need this material for hanging the ceilingSiniat plasterboard. Metal profiles: UD profiles and CD profiles. Direct hangers: Nonius upper and lower parts. Securing clips. Cross connectors. Ceiling dowels / nail dowels. Pallas leveling compounds:

Which horse blanket size?

To find the right size for your horse, you can use the following table as a guide: size S approx. Back length 115-125 cm, size M approx. Back length 130-135 cm, size L approx. Back length 140-145 cm, size XL approx. back length 150-160 cm.

How far do the ceiling hang for spots?

Comment It is best to hang 10 cm, then “almost everything” will obviously fit. Suspending the ceiling by 6 cm is still possible as a compromise, less causes problems with some spots and, if necessary, with less than 6 cm you can help with creative solutions (milling) …

What does 1 square meter of suspended ceiling cost?

What are the costs for a suspended ceiling? If a specialist company for drywall takes over the hanging of the ceiling, costs of 30 to 80 euros per square meter can be expected. In individual cases, these costs can also be significantly exceeded.

How do you make spots in the ceiling?

However, there are two ways of installing LED spots in concrete ceilings: Suspend the ceiling. Let the installation housing set when the concrete ceiling is poured. Make markings and drill recesses. Lay cables. Connect and insert the spots.

What do spots in the ceiling cost?

Spot preparation costs: 416 euros. So including installation or pouring into the concrete 52 euros per piece. This was followed by the precise planning of the ceiling spots.

What is the distance between the LED spots?

The distance from the ceiling spot to the wall should be chosen so that the light edge of the lamp breaks at about 3/4 of the wall height. Depending on the beam angle of the light, you end up with values ​​between 30cm and 100cm. The distance between ceiling spots should be twice as high as the distance from ceiling spots to the wall.

Can spots be built into the concrete ceiling?

The installation of LED spots in a concrete ceiling is not a problem if you already think about it when building a house. Some manufacturers offer special installation housings that are integrated into the concrete plant. Nevertheless, you have to think in advance where the fixtures for the spots have to be placed.

Where do spots make sense?

Spots are often placed between the kitchen island and the wall unit, exactly where no light is needed. You will have more of your spots if you mount these 20 cm from the wall unit to illuminate the cabinet and other spots above the kitchen island so that the work surface is lit.

What do LED spots cost?

1 LED recessed spot (without bulbs) should actually cost 260 flakes.

How many lumens per m2?

For basic lighting in living spaces, 100 lumens per m² are recommended. In “work rooms” such as the kitchen, study or bathroom, a light intensity of up to 300 lumens per m² is perfect.

How many spots in the bathroom?

How many recessed spotlights you need per square meter depends on the luminosity of the lamps. Overall, you should come to the already mentioned 300 lumens per square meter.

How do I connect LED recessed spotlights?

Connect the main power cable 230V (L / N) to the primary side (230V) of the transformer. There are already integrated terminals that are built into the transformer for this purpose. If you only have open cable ends on the transformer, use luster terminals to connect. The protective conductor (PE) does not have to be clamped.

How do I connect an LED lamp?

When connecting the lamp, care must be taken that no bare spots can be seen … The other wires are connected as follows: Neutral – (wire) blue to blue (lamp) phase – (wire) brown to brown (lamp) ground – (Wire) green-yellow, not connected.

What kind of cable do you need for LED?

With 250W connected load and 5m cable length, we recommend a line with at least 2 x 1.5mm² cross-section. 2 x, because plus and minus must be connected.

What is better LED with or without a transformer?

The advantages of LED technology without a transformer predominate Switching to LED technology is always worthwhile. The light-emitting diodes as light sources save a lot of energy and thus electricity costs compared to ordinary light bulbs. An economical operation, but the lights do not lose any of their luminosity.

Why do you need a transformer for LED lamps?

If the voltage deviates upwards or downwards by more than 0.5 V, the light source can be damaged or completely unusable. That is why a transformer is required for LEDs, which always supplies exactly 12 V – these are so-called stabilized transformers or constant voltage transformers.

Can you use halogen transformers for LEDs?

Unfortunately it is not possible to use the electronic halogen transformer with 105 VA, as this type of transformer has to be loaded with a minimum load of 20-35 W. There are now three different ways of avoiding this problem: 1. Connect three additional LED lamps to the halogen transformer.

What kind of transformer with LED?

In principle, the LEDs of the base MR16 LED spotlights and MR11 LED spots as well as G4 LEDs should work with any 12V output voltage transformer. With the usual magnetic transformers (toroidal transformers) there are usually no problems.

Visit the rest of the site for more useful and informative articles!

Leave a Reply

Your email address will not be published. Required fields are marked *